cursor() and noCursor() methods

The Liquid Crystal Library allows you to control LCD displays that are compatible with the Hitachi HD44780 driver. There are many of them out there, and you can usually tell them by the 16-pin interface.

This example sketch shows how to use the cursor() and noCursor() methods to control an underscore-style cursor.

Hardware Required

  • Arduino Board

  • LCD Screen (compatible with Hitachi HD44780 driver)

  • pin headers to solder to the LCD display pins

  • 10k ohm potentiometer

  • 220 ohm resistor

  • hook-up wires

  • breadboard

Circuit

Before wiring the LCD screen to your Arduino board we suggest to solder a pin header strip to the 14 (or 16) pin count connector of the LCD screen, as you can see in the image above. To wire your LCD screen to your board, connect the following pins:

  • LCD RS pin to digital pin 12

  • LCD Enable pin to digital pin 11

  • LCD D4 pin to digital pin 5

  • LCD D5 pin to digital pin 4

  • LCD D6 pin to digital pin 3

  • LCD D7 pin to digital pin 2

Additionally, wire a 10k pot to +5V and GND, with it's wiper (output) to LCD screens VO pin (pin3). A 220 ohm resistor is used to power the backlight of the display, usually on pin 15 and 16 of the LCD connector

click the images to enlarge

LCD Base bb Fritz

image developed using Fritzing. For more circuit examples, see the Fritzing project page

Schematic

click the images to enlarge

LCD Base bb Schem

image developed using Fritzing. For more circuit examples, see the Fritzing project page

Code


/*

  LiquidCrystal Library - Cursor

 Demonstrates the use a 16x2 LCD display.  The LiquidCrystal

 library works with all LCD displays that are compatible with the

 Hitachi HD44780 driver. There are many of them out there, and you

 can usually tell them by the 16-pin interface.

 This sketch prints "Hello World!" to the LCD and

 uses the cursor()  and noCursor() methods to turn

 on and off the cursor.

 The circuit:

 * LCD RS pin to digital pin 12

 * LCD Enable pin to digital pin 11

 * LCD D4 pin to digital pin 5

 * LCD D5 pin to digital pin 4

 * LCD D6 pin to digital pin 3

 * LCD D7 pin to digital pin 2

 * LCD R/W pin to ground

 * 10K resistor:

 * ends to +5V and ground

 * wiper to LCD VO pin (pin 3)

 Library originally added 18 Apr 2008

 by David A. Mellis

 library modified 5 Jul 2009

 by Limor Fried (http://www.ladyada.net)

 example added 9 Jul 2009

 by Tom Igoe

 modified 22 Nov 2010

 by Tom Igoe

 modified 7 Nov 2016

 by Arturo Guadalupi

 This example code is in the public domain.

 http://www.arduino.cc/en/Tutorial/LiquidCrystalCursor

*/

// include the library code:
#include <LiquidCrystal.h>

// initialize the library by associating any needed LCD interface pin
// with the arduino pin number it is connected to

const int rs = 12, en = 11, d4 = 5, d5 = 4, d6 = 3, d7 = 2;

LiquidCrystal lcd(rs, en, d4, d5, d6, d7);

void setup() {

  // set up the LCD's number of columns and rows:

  lcd.begin(16, 2);

  // Print a message to the LCD.

  lcd.print("hello, world!");
}

void loop() {

  // Turn off the cursor:

  lcd.noCursor();

  delay(500);

  // Turn on the cursor:

  lcd.cursor();

  delay(500);
}

See Also

Last revision 2015/08/17 by SM