Send SMS

This sketch send a SMS message from an Arduino MKR GSM 1400. Using the serial monitor of the Arduino Software (IDE), you'll enter the number to connect with, and the text message to send.

Hardware Required

Circuit

MKRGSM1400 bb

Code

First, import the MKRGSM library

#include <MKRGSM.h>

SIM cards may have a PIN number that enables their functionality. Define the PIN for your SIM. If your SIM has no PIN, you can leave it blank :

#define PINNUMBER ""

Initialize instances of the classes you're going to use. You're going to need both the GSM and GSM_SMS class.

GSM gsmAccess;

GSM_SMS sms;

In setup, open a serial connection to the computer. After opening the connection, send a message indicating the sketch has started.

void setup(){

  Serial.begin(9600);

  Serial.println("SMS Messages Sender");

Create a local variable to track the connection status. You'll use this to keep the sketch from starting until the SIM is connected to the network :

boolean notConnected = true;

Connect to the network by calling gsmAccess.begin(). It takes the SIM card's PIN as an argument. By placing this inside a while() loop, you can continually check the status of the connection. When the modem does connect, gsmAccess() will return GSM_READY. Use this as a flag to set the notConnected variable to true or false. Once connected, the remainder of setup will run.

while(notConnected)

  {

    if(gsmAccess.begin(PINNUMBER)==GSM_READY)

      notConnected = false;

    else

    {

      Serial.println("Not connected");

      delay(1000);

    }

  }

Finish setup with some information to the serial monitor.

Serial.println("GSM initialized.");
}

Create a function named readSerial of type int. You'll use this to iterate through input from the serial monitor, storing the number you wish to send an SMS to, and the message you'll be sending. It should accept a char array as an argument.

int readSerial(char result[])
{

Create a variable to count through the items in the serial buffer, and start a while loop that will continually execute.

int i = 0;

  while(1)

  {

As long as there is serial information available, read the data into a variable named inChar.

while (Serial.available() > 0)

    {

      char inChar = Serial.read();

If the character being read is a newline, terminate the array, clear the serial buffer and exit the function.

if (inChar == '\n')

      {

        result[i] = '\0';

        Serial.flush();

        return 0;

      }

If the incoming character is an ASCII character other than a newline or carriage return, add it to the array and increment the index. Close up the while loops and the function.

if(inChar!='\r')

      {

        result[i] = inChar;

        i++;

      }

    }

  }
}

In loop, create a char array named remoteNumber to hold the number you wish to send an SMS to. Invoke the readSerial function you just created, and pass remoteNumber as the argument. When readSerial executes, it will populate remoteNumber with the number you wish to send the message to.

Serial.print("Enter a mobile number: ");

  char remoteNumber[20];

  readSerial(remoteNumber);

  Serial.println(remoteNumber);

Create a new char array named txtMsg. This will hold the content of your SMS. Pass txtMsg to readSerial to populate the array.

Serial.print("Now, enter SMS content: ");

  char txtMsg[200];

  readSerial(txtMsg);

Call sms.beginSMS() and pass it remoteNumber to start sending the message, sms.print() to send the message, and sms.endSMS() to complete the process. Print out some diagnostic information and close the loop. Your message is on its way!

Serial.println("SENDING");

  Serial.println();

  Serial.println("Message:");

  Serial.println(txtMsg);

  sms.beginSMS(remoteNumber);

  sms.print(txtMsg);

  sms.endSMS();

  Serial.println("\nCOMPLETE!\n");
}

Once your code is uploaded, open the serial monitor. Make sure the serial monitor is set to only send a newline character on return. When prompted to enter the number you wish to call, enter the digits and press return. You'll then be asked to enter your message. Once you've typed that, press return again to send it.

The complete sketch is below.


/*

 SMS sender

 This sketch, for the MKR GSM 1400 board,sends an SMS message

 you enter in the serial monitor. Connect your Arduino with the

 GSM shield and SIM card, open the serial monitor, and wait for

 the "READY" message to appear in the monitor. Next, type a

 message to send and press "return". Make sure the serial

 monitor is set to send a newline when you press return.

 Circuit:

 * MKR GSM 1400 board

 * Antenna

 * SIM card that can send SMS

 created 25 Feb 2012

 by Tom Igoe

*/

// Include the GSM library
#include <MKRGSM.h>

#include "arduino_secrets.h"
// Please enter your sensitive data in the Secret tab or arduino_secrets.h
// PIN Number

const char PINNUMBER[] = SECRET_PINNUMBER;

// initialize the library instance

GSM gsmAccess;

GSM_SMS sms;

void setup() {

  // initialize serial communications and wait for port to open:

  Serial.begin(9600);

  while (!Serial) {

    ; // wait for serial port to connect. Needed for native USB port only

  }

  Serial.println("SMS Messages Sender");

  // connection state

  bool connected = false;

  // Start GSM shield

  // If your SIM has PIN, pass it as a parameter of begin() in quotes

  while (!connected) {

    if (gsmAccess.begin(PINNUMBER) == GSM_READY) {

      connected = true;

    } else {

      Serial.println("Not connected");

      delay(1000);

    }

  }

  Serial.println("GSM initialized");
}

void loop() {

  Serial.print("Enter a mobile number: ");

  char remoteNum[20];  // telephone number to send sms

  readSerial(remoteNum);

  Serial.println(remoteNum);

  // sms text

  Serial.print("Now, enter SMS content: ");

  char txtMsg[200];

  readSerial(txtMsg);

  Serial.println("SENDING");

  Serial.println();

  Serial.println("Message:");

  Serial.println(txtMsg);

  // send the message

  sms.beginSMS(remoteNum);

  sms.print(txtMsg);

  sms.endSMS();

  Serial.println("\nCOMPLETE!\n");
}

/*

  Read input serial

 */
int readSerial(char result[]) {

  int i = 0;

  while (1) {

    while (Serial.available() > 0) {

      char inChar = Serial.read();

      if (inChar == '\n') {

        result[i] = '\0';

        Serial.flush();

        return 0;

      }

      if (inChar != '\r') {

        result[i] = inChar;

        i++;

      }

    }

  }
}

See Also:

Last revision 2017/11/29 by AG