Connect With WEP

This example shows you how to connect to a WEP encrypted 802.11b/g network with the Arduino WiFi shield 101 or a MKR1000 board. Your Arduino Software (IDE) serial monitor will provide information about the connection once it has connected.

Hardware Required

  • Arduino WiFi Shield 101
  • Arduino or Genuino Zero board

or

  • MKR1000

Circuit

Digital pin 7 is used as a handshake pin between the WiFi Shield 101 and the board, and should not be used.

You should have access to a 802.11b/g wireless network that connects to the internet for this example. You will need to change the network settings in the sketch to correspond to your particular networks SSID.

WEP network passwords are hexadecimal strings known as keys. A WEP network can have 4 different keys; each key is assigned a "Key Index" value. For WEP encrypted networks, you need the SSID, the key, and key number.

image developed using Fritzing. For more circuit examples, see the Fritzing project page

In the above image, the Arduino or Genuino Zero board would be stacked below the WiFi shield.

Code

/*

 This example connects to a WEP-encrypted WiFi network.
 Then it prints the  MAC address of the WiFi shield,
 the IP address obtained, and other network details.

 If you use 40-bit WEP, you need a key that is 10 characters long,
 and the characters must be hexadecimal (0-9 or A-F).
 e.g.  for 40-bit, ABBADEAF01 will work, but ABBADEAF won't work
 (too short) and ABBAISDEAF won't work (I and S are not
 hexadecimal characters).

 For 128-bit, you need a string that is 26 characters long.
 D0D0DEADF00DABBADEAFBEADED will work because it's 26 characters,
 all in the 0-9, A-F range.

 Circuit:
 * WiFi shield attached

 created 13 July 2010
 by dlf (Metodo2 srl)
 modified 31 May 2012
 by Tom Igoe
 */

#include <SPI.h>
#include <WiFi101.h>

#include "arduino_secrets.h"
///////please enter your sensitive data in the Secret tab/arduino_secrets.h
char ssid[] = SECRET_SSID;        // your network SSID (name)
char key[] = SECRET_PASS;    // your network password (use for WPA, or use as key for WEP)
int keyIndex = 0;                                // your network key Index number
int status = WL_IDLE_STATUS;                     // the WiFi radio's status

void setup() {
  //Initialize serial and wait for port to open:
  Serial.begin(9600);
  while (!Serial) {
    ; // wait for serial port to connect. Needed for native USB port only
  }

  // check for the presence of the shield:
  if (WiFi.status() == WL_NO_SHIELD) {
    Serial.println("WiFi shield not present");
    // don't continue:
    while (true);
  }

  // attempt to connect to WiFi network:
  while ( status != WL_CONNECTED) {
    Serial.print("Attempting to connect to WEP network, SSID: ");
    Serial.println(ssid);
    status = WiFi.begin(ssid, keyIndex, key);

    // wait 10 seconds for connection:
    delay(10000);
  }

  // once you are connected :
  Serial.print("You're connected to the network");
  printCurrentNet();
  printWiFiData();
}

void loop() {
  // check the network connection once every 10 seconds:
  delay(10000);
  printCurrentNet();
}

void printWiFiData() {
  // print your WiFi shield's IP address:
  IPAddress ip = WiFi.localIP();
  Serial.print("IP Address: ");
  Serial.println(ip);
  Serial.println(ip);

  // print your MAC address:
  byte mac[6];
  WiFi.macAddress(mac);
  Serial.print("MAC address: ");
  Serial.print(mac[5], HEX);
  Serial.print(":");
  Serial.print(mac[4], HEX);
  Serial.print(":");
  Serial.print(mac[3], HEX);
  Serial.print(":");
  Serial.print(mac[2], HEX);
  Serial.print(":");
  Serial.print(mac[1], HEX);
  Serial.print(":");
  Serial.println(mac[0], HEX);
}

void printCurrentNet() {
  // print the SSID of the network you're attached to:
  Serial.print("SSID: ");
  Serial.println(WiFi.SSID());

  // print the MAC address of the router you're attached to:
  byte bssid[6];
  WiFi.BSSID(bssid);
  Serial.print("BSSID: ");
  Serial.print(bssid[5], HEX);
  Serial.print(":");
  Serial.print(bssid[4], HEX);
  Serial.print(":");
  Serial.print(bssid[3], HEX);
  Serial.print(":");
  Serial.print(bssid[2], HEX);
  Serial.print(":");
  Serial.print(bssid[1], HEX);
  Serial.print(":");
  Serial.println(bssid[0], HEX);

  // print the received signal strength:
  long rssi = WiFi.RSSI();
  Serial.print("signal strength (RSSI):");
  Serial.println(rssi);

  // print the encryption type:
  byte encryption = WiFi.encryptionType();
  Serial.print("Encryption Type:");
  Serial.println(encryption, HEX);
  Serial.println();
}

See Also:

  • WiFi library – Your reference for the WiFi101 Library.
  • WiFi Shield – Product details for the WiFi 101 Shield.
  • MKR1000 – Product details for the MKR1000 board.



Last revision 2016/04/16 by SM

Share